Chimney flashings
The gap between chimney and tiles is sealed with lead stepped flashings. When they crack or pull away, that's usually where the leak starts.
Lead flashings, valleys and chimney details are where most roof leaks start. SB Roofing repairs and replaces them, stopping water getting in before it stains ceilings and rots timbers.
On every leadwork job
Lead is the premium flashing material for roofs because it lasts 300 years or more, moves with the building without cracking, and self-heals minor damage. It's also expensive and needs proper installation. We repair leaking lead details, replace failed sections and install new lead where tiles alone can't stop water getting in.
The gap between chimney and tiles is sealed with lead stepped flashings. When they crack or pull away, that's usually where the leak starts.
Where a roof meets an external wall or gable, lead flashing carries water safely down to the tile below and down the wall to the gutter.
The V-shaped junction where two roof slopes meet. Lead valleys shed water faster than tiled valleys and don't need covering with tiles.
Gutters built into the roof structure are lined with lead to carry water to the downpipes without damaging the tiles beneath.
Windows in roofs need careful flashing to manage water runoff. Lead flashings stop drips from seeping past the frame.
Where lead ridges and hips end at gables or walls, the lead must be turned and sealed so water runs off, not under.
Lead develops problems slowly, but once water starts getting past it, the damage spreads fast. Look for these signs before the ceiling stains appear.
Often run up and down. Lead can fatigue and crack from movement, or corrosion if certain types of timber or mortar touch it.
Nails rust or loosen, and the flashing lifts at the edges, leaving a gap where water gets through.
Green is verdigris, a natural patina. White crusts are lead carbonate, usually harmless but worth checking.
Water seeping past the flashing shows up on ceilings or walls below the roof.
Often appear after rain. Points to a failure in the flashing between roof and brickwork.
Heavy snow or poor support can deform lead. It won't stop leaking until it's re-flattened or replaced.
Lead is valuable. Old lead flashings are targeted for theft. If yours are missing or removed, replace them quickly or the problem underneath will get worse.
Lead flashings are graded by weight per square metre. Heavier lead lasts longer and resists damage better, so the code you choose affects both cost and longevity.
The minimum for most applications. Used where the lead isn't exposed to foot traffic or sharp impacts. Acceptable for small roof valleys and low-wear flashings.
The most common choice for chimney flashings, roof-to-wall junctions and standard valleys. Good balance of weight, durability and cost.
Heavy-duty lead for valleys that catch a lot of water, gutters, and areas exposed to foot traffic or weather. Worth the extra cost on exposed roofs.
Codes 4 and 5 cost less and are easier to work with. They're fine for protected details but may fatigue or dent if exposed.
Codes 6 and above resist impact and weathering better. The extra weight costs more upfront but means 20+ extra years of service life.
Reclaimed lead is cheaper but its history is unknown. New lead code is marked on the roll, so you know exactly what you're getting.
The quote covers the work, the lead and the finish. No hidden bills once we start.
Lead flashings are deceptively simple-looking, but the detail is what stops leaks. We follow the Code of Practice and take time to get the folds and seals right.
Scott traces where the water is getting in, checks the condition of the roof timbers and decides what needs replacing or repairing.
You get a written quote showing the lead code, the extent of the work and what it will cost. Lead prices change, so we quote at the time you book.
Tiles above the flashing are carefully removed, the old lead is peeled back and taken off, and the substrate is checked for rot.
The roof surface is cleaned, levelled if needed and covered with roofing felt where the new lead will sit, so it doesn't corrode from contact with the timber.
The lead is cut, formed to shape, and nailed down with corrosion-resistant fixings. Folds and seals are made carefully to Code of Practice standard.
Tiles are refixed, the lead is inspected for any sharp edges and we walk you through what's been done and how to care for it.
If you're uncertain about approval, ask us or your local building control team.
We don't estimate leadwork over the phone. A proper look and measurement is free.
New lead needs almost no maintenance. A few simple practices will keep it trouble-free for decades.
Green or white marks on lead are natural corrosion that actually protect it. Don't scrub or polish it off.
Blocked gutters overflow onto the lead, forcing water into places it shouldn't go. Clear them twice a year.
High winds and heavy snow can lift or bend lead. A quick look from the ground after extreme weather is worthwhile.
If mortar, paint or copper (which corrodes lead) touch the lead, wash it off. Different metals in contact can cause galvanic corrosion.
Lead flashings are part of a wider system. These jobs often happen alongside leadwork to stop leaks properly.
Tiles around lead details often need refixing or replacing when flashings are renewed.
Find out more →New gutters and downpipes ensure water from your roof is carried safely away from the walls and foundations.
Find out more →Foam under tiles traps damp against roof timbers. We remove it so you can see what the timber condition really is before new lead goes on.
Find out more →Code 4 lead typically lasts 20–40 years. Code 5 lasts 40–60 years. Code 6 and above can last 60+ years or longer. The life depends on the code, exposure to weather, and how well it's installed and maintained. Lead in a sheltered valley lasts longer than lead on an exposed, south-facing chimney.
Small cracks can sometimes be soldered if the lead is in good condition overall. But if the flashing is thin, corroded or has lifted in several places, replacement is usually better value. We'll tell you on the visit which option makes sense. Full replacement ensures it lasts another 40–60 years.
Green is verdigris, a natural patina that actually protects the lead underneath. It's not corrosion. Don't scrub it off; the exposed lead underneath will corrode faster. Leave it alone and your lead will last longer.
Code 5 is 2.24 mm thick; Code 6 is 2.65 mm. Code 6 is heavier, more resistant to impact and foot traffic, and lasts 20+ years longer. It costs more upfront but represents better value over the life of the roof. For high-traffic areas or exposed valleys, Code 6 is worth the extra.
Repair or replacement of existing flashings usually doesn't need approval. A full roof renovation might. If you're in a conservation area or your building is listed, check with your local council before we start, as heritage planning rules may apply.
Yes. Old lead is valuable and easily recycled. We remove it carefully, bag it and ensure it goes to a licensed recycler. The scrap value often goes towards offsetting the cost of the new lead.
Send Scott a photo of the cracked or leaking area, or we'll arrange a free visit to trace where the water is getting in and quote to fix it properly.
01225 123456Ready to start
WhatsApp is the quickest way to send photos and get a quick response. Or use the contact page to leave the details.
Message on WhatsApp Request a free quote Leadwork in Bath