Skip to content

Leadwork in Bath

Lead flashings, valleys and roof abutments last 60+ years when done right, but fail quietly — water seeps in along mortar joints and under tiles long before you notice. SB Roofing replaces, re-dresses and repairs lead on Bath roofs, from valley flashings to chimney stacks. Scott will tell you straight which bits are worth fixing and which need replacing.

  • Free, no-obligation survey
  • Fully insured
  • Work guaranteed to last
Lead valley and flashing work on a Bath roof

Bath properties

Where lead fails on Bath roofs

Bath's mix of Georgian terraces, Victorian semis and period homes all rely on lead to seal the joins and angles where tiles meet walls and chimneys. Lead is the problem child only where it has been neglected.

Chimney flashings on terraces

Terraces have a chimney on the ridge or at the gable end. Lead flashing round it fails when the mortar holding the lead to the brickwork cracks. You will not see water until it has travelled into the loft and shows on a ceiling beam.

Roof valleys on larger homes

Where two roof slopes meet in a valley, the lead lining can creep and fold if the nails have rusted or come loose. A crease in the lead forces water to run up instead of down. Re-laying the lead properly stops the leak for life.

Abutment flashings on extensions

Where a roof butts against a wall — often a later extension or a dormer — lead needs to be tucked under the mortar and folded up the wall. Poor installation or movement in the building soon opens gaps that let water in.

Hip and ridge details

Lead is sometimes used under hip and ridge bedding instead of mortar, particularly on older homes. When it fails, the whole line of tiles is at risk. Replacing it with lead and proper clips is the lasting fix.

Lead flashing being dressed and sealed on a Bath roof

★★★★★

"Scott came to give an estimate of costs and said he could reseal the lead immediately. The leak was thus sealed without further delay and the cost a very reasonable call out fee."

Google review

How we do it

Lead repair and replacement, step by step

  1. Inspect and diagnose

    Scott goes up and traces where the water is coming in. That often means looking at the chimney from inside the loft, or running water over the valley and watching where it leaks through. Diagnosis beats guesswork.

  2. Explain the options

    Some lead can be re-dressed and sealed. Some needs pulling out and replacing with new lead Code 4 — the thickness for roofs. You get the choice and a price for each before anything is stripped.

  3. Remove and re-lay

    Tiles or slates covering the lead come off. Old lead is stripped. New lead is cut, laid, nailed and dressed so water runs off it in one direction. Mortar and sealant are applied to bed it to the wall or brickwork.

  4. Re-tile and tidy

    Tiles are re-fixed and sealed. Lead is worked into the tile mortar at the junction. Everything is swept, the garden is cleared and you get a tidy job left behind.

Cost factors

What moves the price on lead work

Lead prices fluctuate, but the real cost is in getting to the work safely and doing it to last. These are the variables we walk through on a site visit.

Repair or replacement

Re-dressing and sealing existing lead is a quick fix for some jobs. Stripping old lead and laying new takes longer and costs more, but fixes it for 60+ years.

How much lead

A chimney flashing is a few metres. A valley across a large roof can be 10+ metres. The more lead, the longer the job and the higher the material cost.

Access and working height

A single-storey cottage is safer and quicker to work on. A four-storey Georgian terrace or a steeply pitched roof may need scaffold, harnesses or a longer day.

Existing condition underneath

If tiles or slates come off and the battens or timbers underneath are rotten, that is extra work and cost. We tell you before carrying on.

Neighbouring roofs and party walls

On terraces, lead flashing often sits on a party wall. We plan access with neighbours early and flag any consent that might be needed.

Lead price at the time

Lead is priced on the global market. We quote to the price on the day of the visit, and confirm it again before ordering.

On the ground in Bath

Practical details for lead work in the city

  • Terraced streets and narrow access

    Many Bath properties sit on steep streets or have no rear access. We plan where the van parks and where materials are stored before the job starts, and we sort any pavement licence early.

  • Party wall issues

    Lead flashing often sits on a shared wall or touches a neighbour's roof. We tell you if that is the case at quote stage and advise whether a formal notice is needed.

  • Living on site during work

    Lead work can take a day or two. The roof is weathertight while we work, and we do not expect you to move out for a flashing repair or valley replacement.

Questions

Lead work questions we answer

Unsure if your leak is lead-related? Message Scott with a photo and he will advise what it needs.

How long does lead flashing last?

Lead Code 4 (roof weight) lasts 60–80 years or more if installed and dressed properly. It fails when nails rust, mortar cracks or the lead is not dressed — not because lead itself wears out. SB Roofing replaces it to last, not just patched up.

Can you repair lead or does it need replacing?

Some lead can be re-dressed, sealed and left in place — if the base is sound and it is not creased or torn. Other lead is split, folded or sitting on rotten wood underneath, in which case it needs pulling out and replacing. Scott looks at it on site and gives you both options and prices.

Why do flashing leaks take so long to show inside?

Water gets in at the flashing, then travels along the roof timbers or down the inside of the wall. It can travel metres before it pools and shows as a damp patch or stain on a ceiling. That is why a live leak can be hard to trace — it enters at the chimney but shows up in a room on the other side of the roof.

What is Code 4 lead?

Code 4 is the thickness standard for roof flashings — it is 2 mm thick. Code 3 (thinner) is used for smaller items. Roof lead must be Code 4 to resist wind and weather for decades.

Do I need neighbour permission for lead work on a party wall?

In many cases, yes. The Party Wall etc. Act 1996 applies if you are going to cut into a neighbour's wall or remove and replace lead on a shared structure. We tell you if it applies to your job and advise on the notice needed.

How much does lead flashing repair cost?

Lead prices vary week to week, so we quote after a site visit. The cost depends on how much lead is needed, whether it is repair or full replacement, access, and the complexity of the flashing. A chimney flashing is usually a day's work; a valley across a large roof can take longer. You get a fixed price before we start.

Water getting in around a flashing or valley?

Tell Scott what you can see — damp patches on a ceiling, water staining on a loft beam, or just a soft spot in the mortar — and he will come out, trace where it is coming from and give you a free survey and quote.